Lagondaforum

Hello Guest! (New posts) Forum


Expand and collapse Topic Options
Pages (7): [1] [2][3][4][5][6][7]
 Show first unread post

Jun 27, 2011 7:03 pm
bill Offline
Member
Registered since: Jun 08, 2011
Location: -


Subject: Re: G9 gearbox
Just a final word on the G9 if anyone else is tempted to rebuild theirs. Mine is now back together but I have only done one short trip so far. Everything works fine but only time will tell !
However, I cannot stress how important I think it is to clean out the oilways in the gears. I dont think there is much point in rebuilding the gearbox if you do not do this. Second gear is quite easy once you have pushed the bush out. However 3rd and 4th are much more of a challenge as the actual double helical gear itself must be pushed off the steel syncro "housing" (for want of a better word). Each gear is on 2 keyways and you will need 2 hardened steel pins to assist in pushing it off (and a hydraulic press). This was very very difficult but it is only by getting the gears off that you can properly clean out the oil holes and tracks. 3rd gear bush relies on the oil getting through as otherwise it will seize on the mainshaft presumably. Just as importantly the oil ways in 4th gear allow oil to get through to the little bush on the nose of the output shaft and inside the input shaft.
Best of luck to anyone else who decides to have a go !
 

Jun 28, 2011 1:30 am
bruffsup Offline
Member
Registered since: Aug 08, 2010
Location: Canada


Subject: Re: G9 gearbox
Well you can forget about all that bragging from me about having a perfect gearbox! Closer inspection revealed a few missing teeth on the herringbone gears. Owch! In the past with Harley and other motorcycle boxes I have successfully built up teeth with a specialist oxy acetylene rod , called "sif bronze" on this side of the pond. I suppose I will give it a go as long as there are not 2 adjacent teeth it seems to hold up. Of course if new gears are available I will go that route.
Thanks for the info guys, it's a great help.
Barry Brown
Barry Brown
Bedford Mills Ontario Canada
 

Jun 28, 2011 7:58 pm
Colin M34 Offline
Member
Registered since: Dec 01, 2007
Location: Suffolk, UK


Subject: Re: G9 gearbox
Hi Barry,

Dental problems on M45 gearboxes can be solved! I believe you have a T8 not a T9 gearbox.Please correct me if I am wrong. Take a look at part number GRS419 on the Lagonda Club spares website at http://lagondaclub.co.uk/spares/acatalog/Parts_catalogue_T8__T9_and_G10__gearboxes_118.html

Does this look the correct part? If so, we have them in stock, assuming you are a Lagonda Club member...

Colin M34
This post has been edited 1 times. Last edit on Jun 28, 2011 8:00 pm by Colin Mallett.  

Jun 28, 2011 11:22 pm
bruffsup Offline
Member
Registered since: Aug 08, 2010
Location: Canada


Subject: Re: G9 gearbox
Thank you Colin, It looks promising and yes I am a member. Thank goodness I can avoid the vat at 20% but of course with the shipping and our own dreaded GST it works out equally painfull!
Barry Brown
Barry Brown
Bedford Mills Ontario Canada
 

Jun 29, 2011 2:22 pm
Julian Offline
Member
Registered since: Dec 04, 2007
Location: Belgium


Subject: Re: G9 gearbox
Hi Barry,

A little shameless plug for ourselves too,

We can supply a complete "gearbox kit" with all 10 gears and 4 shafts complete with complete bearing set etc, for 5260 Euros or about 4500 GB depending on exchange rate.

Maybe worth a thought if you want to go the whole hog!

Regards,
Julian
Julian Messent
 

Jun 29, 2011 10:23 pm
Colin M34 Offline
Member
Registered since: Dec 01, 2007
Location: Suffolk, UK


Subject: Re: G9 gearbox
Hi Julian,

Your "whole hog" T8 gearbox internals kit looks pretty attractive to my eyes. Presumably LMB could also fit these bits into an existing box. Any idea how much this would cost?

Colin M34
 

Jun 30, 2011 7:24 am
Julian Offline
Member
Registered since: Dec 04, 2007
Location: Belgium


Subject: Re: G9 gearbox
Hi Colin,
thanks for the question,
Yes, usually we charge about 1800 euro for a complete box rebuild, (we take about 25 hours from start to finish) that means the full box given to us, we strip it, repair any threads etc, de-burr and slightly modify the selector shaft holes, chemical clean it and then rebuild with our kit etc, We then test it running on a modified lathe to ensure all is working well, and with No leaks which is not an easy task on these ;o)
However I have just quoted an English customer for one that is coming over in a couple of weeks and we try to be flexible on the fitting cost as I am well aware it is not an easy pill to swallow!

In case of emergency, it's worth noting that we carry a complete gearbox, fully rebuilt with our gears and shafts etc "in stock" ready to be shipped immediately if someone is in dire need!

Very best regards,
Julian,


Julian Messent
This post has been edited 1 times. Last edit on Jun 30, 2011 7:33 am by Julian.  

Jul 04, 2011 8:28 pm
bill Offline
Member
Registered since: Jun 08, 2011
Location: -


Subject: Re: G9 gearbox
Dear Julian
Just a further post with regard to Colin's post about your complete gearbox internals for a T8 gearbox.
I agree that seems a very fair price particularly bearing in mind that everything will presumably match everything else.
Just in case my gearbox rebuild goes horribly wrong do you do a complete set of internals for the G9 and how much does that work out landed in the UK ? What exactly is included in that "kit".
Is everything finished to go straight into the casing or is further honing/reaming required ?
Many thanks again for your help
Bill
 

Jul 07, 2011 11:52 am
Julian Offline
Member
Registered since: Dec 04, 2007
Location: Belgium


Subject: Re: G9 gearbox
Afternoon Bill,

We do indeed stock G9 box sets also,
This is the full monty with everything included including synchro hubs and bronze linings, but does not include the round cage that goes over the main synchro hub. This never wares and only holds the balls in place, so would be silly to manufacture, the centre part of the main hub with the fine dog ring teeth on it though is included and this is matched to the new synchro hubs on 3rd and 4th.

The attachment shows the kit but you also get the reverse shaft and bronze syncro friction rings etc.
Price is I am afraid 8850 euros as it is rather more complex box and the usual problem is dog ring teeth wearing tapered meaning there is no getting away from the expensive parts for us Embarrassing(

Hope this helps but actually hoping you won't need them!

Very best regards,
Julian

PS.
Always here to help if you need advice on repairs etc, Just mail me or phone, very happy to help in any way! And that bit is FREE! Embarrassing)

Thumbnails of attached images:

Filename: 2011small.jpg
Filetype: File Type Information for: jpg jpg
Downloads: 725
Filesize: 95.53 KB
Image size: 615 x 461 Pixels


Julian Messent
 

Jul 10, 2011 11:17 pm
peter weir Offline
Member
Registered since: Dec 03, 2009
Location: Oban Scotland


Subject: Re: G9 gearbox
I've noted with interest the G9 rebuild tips, I've got mine to start as it's got a broken 3d gear tooth. I purchased a second hand gear from the Club's 'Leo' collection which looks the same but after the article in the last magazine I hope it's the correct gear angle!
I've also been collecting parts over the last 10 years for my M45 saloon 'body back to car' rebuild project and managed to purchase a T8 gearbox. It was removed from a car in the 1950's when the owner got a recondioned 'exchange' box from The Lagonda Co but for some reason the duff box was never returned but lay under the garage bench for 50 years.
From a superficial look the gears look OK - no broken teeth but the original problem was that it jumped out of third gear. Has anyone experienced this problem and what is the cure? An idea of the problem will give me some idea for my future workload.
 

Pages (7): [1] [2][3][4][5][6][7]


All times are GMT