Lagondaforum

Hello Guest! (New posts) Forum


Expand and collapse Topic Options
Pages (1): [1]
 Show first unread post

Jul 19, 2011 2:35 pm
randall977 Offline
Member
Registered since: Oct 29, 2010
Location: Oxfordshire


Subject: Unleaded Conversion...
Mainly because I'm bored of seeing 'head removal tool' as the only topic in this section, I have a question; What good reason is there (based upon fact) to convert a DB5 engine to unleaded? It already has hardened valve seats which were fitted in the factory, it is unlikely that an after market replacement will be any better...discuss
Christian
 

Jul 19, 2011 8:40 pm
TVJL Offline
Member
Registered since: Dec 04, 2007
Location: London


Subject: Re: Unleaded Conversion...
Not much to discuss, I'm afraid. The answer is 'none'. Crazy
 

Jul 20, 2011 10:23 am
h14 Offline
Member
Registered since: Nov 30, 2008
Location: Chalandray, France


Subject: Re: Unleaded Conversion...
Not sure of the context here, but perhaps "conversion" referred to altering the ignition timing to suit unleaded petrol? I seem to recall that when unleaded was introduced, charts were available showing what changes to make.
 

Jul 20, 2011 6:43 pm
Colin M34 Offline
Member
Registered since: Dec 01, 2007
Location: Suffolk, UK


Subject: Re: Unleaded Conversion...
Hang on folks...

Surely the DB5 has an alloy head so 'of course' it would already have steel valve seat inserts...
Also, playing around with ignition timing is needed with all our old cars to match the burn characteristics of modern fuels.

Colin
 

Jul 21, 2011 1:26 pm
TVJL Offline
Member
Registered since: Dec 04, 2007
Location: London


Subject: Re: Unleaded Conversion...
Indeed. Grinning
 

Jul 22, 2011 1:44 pm
David Offline
Member
Registered since: Feb 05, 2011
Location: -


Subject: Re: Unleaded Conversion...
Having had 2 engines done, as good a reason as any is to return the head, seats, valves, springs, colletts, guides, tappets etc returned to new condition and clearances using more modern materials as necessary than were available when the head assembly was designed in 1957-58. Unleaded also burns hotter than 4-star so attention should also be paid to all aspects of cooling, especially in the head around the exhaust valve guides which are cooled directly by the water flow, and in general around cylinders 5 and 6 where flow is reportedly weaker than elsewhere
 

Jul 23, 2011 7:06 am
Colin M34 Offline
Member
Registered since: Dec 01, 2007
Location: Suffolk, UK


Subject: Re: Unleaded Conversion...
David's comments about fuel apply equally to all of our cars. My 1925 12/24 Lagonda ran very hot and so using modern materials for valves and seats is as valid for it as well. There is also a lot of knowledge and expertise on how to improve the circulation on the M45 Meadows engine to run cooler.

Not only does unleaded burn hotter, but with low compression engines it burns slower, hence the need to advance the timing to get the flame well and truly alight before the exhaust valve opens. The late Arthur Jeddere-Fisher, stalwart of the VSCC and legal counsel to HMRC had the law changed to allow people to legally "cut" their petrol with kerosene (heating oil) to try and alleviate this problem, particularly with Edwardian motor cars. The mixing had to be done in the car's petrol tank.

Colin
 

Jul 23, 2011 12:03 pm
bruffsup Offline
Member
Registered since: Aug 08, 2010
Location: Canada


Subject: Re: Unleaded Conversion...
Colin, Can you please elaborate on on the M45 circulation mods ? Thanks, Barry
Barry Brown
Barry Brown
Bedford Mills Ontario Canada
 

Pages (1): [1]


All times are GMT