Lagondaforum

Hello Guest! (New posts) Forum


Expand and collapse Topic Options
Pages (1): [1]
 Show first unread post

Jan 28, 2014 9:58 am
cahallett Offline
Member
Registered since: Apr 02, 2012
Location: -


Subject: 16/80 head gasket problems
16/80 head gasket problems

Dear All,
Any opinions to the following would be welcome.

After a spirited 100 mile run last September I noticed the presence of emulsion on the oil dip stick and under the oil filler cap on the rocker cover.
No oil was present when looking into the radiator cap but upon draining the engine oil you could see evidence of coolant/water.

Up until this point the car has performed faultlessly since its engine rebuild some 7,000miles ago (the block face and cylinder head face were skimmed & checked for flatness and both the head and block had been crack/pressure tested).

Open removal of the head no evidence of a blown gasket was apparent.
That said, the cylinder head inspection plate at the rear was fouling somewhat on that strange little bit of casting to the top rear of the block (see picture).

It was noticed that one or two of the new head studs had become loose and on a couple of studs the nuts had siezed so the whole stud had to be replaced.

The head and block were then cleaned a new gasket fitted, this time with wellseal on all faces (previously it had been fitted dry).
Three studs were replaced and new nuts used and all were then tightened down in sequence, 10ft lbs at a time (left for 15 minutes and then tightened down a further 10ft lbs until 40ft lbs was achieved).
It was then tightened again the following morning and the valve/tappet clearances were checked and then double checked (I set these to 8 thou always as a precaution).

A few weeks later when I had finally refitted the exhaust the car was taken for a short run.
The pick-up was sluggish and on deceleration it would POP POP POP quietly.

My initial thought was that I had not sealed the exhaust sufficiently so last Friday before the run up to Cambridge for the New Year’s Dinner I had the exhaust off and re-fitted.
The run up to Cambridge was rough, the pick-up terrible and the car would POP POP POP on acceleration and hard deceleration.
Oil pressure was good (50 – 60 psi at 50 mph, 20 psi on idle), Radiator temperatures were also normal for my car in this cold weather (60 degrees).

However, upon removal of the oil filler cap on the rocker cover, emulsion was present (could it be residue left over from before?).

A compression test was conducted yesterday and each cylinder is around 18-20psi down on the test conducted before the head gasket change.
•   Before head gasket change on 1 to 6 cylinders = 122 to 118psi
•   After head gasket change on 1 to 6 cylinders = 101 to 106psi

So, what to do now.
My initial thoughts are to check the valve/tappet clearances again just to make sure I did not do anything stupid.
Failing that its head off, gasket off, clean away all traces of the wellseal, check that the surfaces are flat, replace all head studs and nuts and try again (this time dry fitting the gasket with a smear of oil),

Any suggestions?


Thumbnails of attached images:

Filename: Castin to rear of block (2).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 814
Filesize: 167.74 KB
Image size: 1024 x 768 Pixels

Filename: Castin to rear of block (1).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 846
Filesize: 155.58 KB
Image size: 1024 x 768 Pixels

Filename: CLUB CYLINDER HEAD STUDS (1).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 789
Filesize: 70.84 KB
Image size: 576 x 768 Pixels

Filename: Emulsion 26-09-13 (2).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 822
Filesize: 135.72 KB
Image size: 1024 x 768 Pixels

Filename: Emulsion in oil filler cap.jpg
Filetype: File Type Information for: jpg jpg
Downloads: 739
Filesize: 94.70 KB
Image size: 1024 x 768 Pixels

This post has been edited 4 times. Last edit on Jan 29, 2014 9:56 am by cahallett.  

Jan 29, 2014 10:08 am
ray sherratt Offline
Member
Registered since: Jul 05, 2012
Location: wirral cheshire


Subject: Re: 16/80 head gasket problems
Have you upset the carb settings in any way leaving her
lean on power and overun. As for the water emulsion could
it be a cracked block in the bore? You mentioned a plate
at the rear of the head possibly holding the head from
sealing, has this been rectified. Are the replacment nuts
the same size as in the picture, if so thy look small in depth
they should be at least 1.5 to 2 times thread diam in thickness.

Ray.
 

Jan 29, 2014 11:05 am
cahallett Offline
Member
Registered since: Apr 02, 2012
Location: -


Subject: Re: 16/80 head gasket problems
Hello Ray,
Thanks for the reply.
The carbs settings have not been touched (I also mark the current setting with a little piece of wire so I always no where they are if any changes are made).
The block was totally restored 7,000miles ago, machined, sleeved and pressure tested (I cannot see how I could cracked it but if everything else checks out OK then it will need investigating).
Regarding the plate at the rear of the block, yes this has been reduced slightly in depth to give adequate clearance.
Now as for the studs, these are new stock from the club along with the nuts.

Best Regards
Chris
 

Jan 29, 2014 7:42 pm
ray sherratt Offline
Member
Registered since: Jul 05, 2012
Location: wirral cheshire


Subject: Re: 16/80 head gasket problems
Hi Chris
When the head was removed was there any sign of water
mark in the bore. If you havent removed the head yet, make
up a presure test adaptor out of an old spark plug, to screw
into the head and conect to your air line. Put the car in top gear with test cylinder at compresion TDC, hand brake on.
Make sure the radiator is filled to the top, and put as much presure as you can into the cylinder and watch the rad. If you have a CO2 bottle this will give you greater presure.

Ray.
 

Jan 30, 2014 10:19 am
cahallett Offline
Member
Registered since: Apr 02, 2012
Location: -


Subject: Re: 16/80 head gasket problems
Hello Ray,
No signs of water whatsoever when the old gasket was removed.
I did notice that the spark plugs were all a white/light grey after the last run (even No.6) so that may indicate the presence of water in the combustion chamber and the rough running etc…
Your test sounds a good idea so if the children give me some free time this weekend I will try it.

Thanks for your advice
Chris
 

Jun 24, 2014 3:34 pm
cahallett Offline
Member
Registered since: Apr 02, 2012
Location: -


Subject: Re: 16/80 head gasket problems = dropped cylinder liners
Well just in case anybody is interested here is the update on my head gasket failure.

In a nutshell it is due to No.5 & No.6 cylinder liners having dropped slightly (how did I not spot it when the head was off last I don’t know --- old age and failing eyesight I guess).
It is possible the engine overheated in Tuscany last year as the hill/mountain passes were quite steep and on one occasion we did have some loss of power which I put down to altitude at the time.

The strange thing is that with the exception of that one occurrence the car had been running faultlessly.

So I am resigned to the fact that the engine will have to come out, dismantled and be thoroughly inspected.
I hope after having read the recent 4.5L Meadows engine saga it will just be a case (just) of having the liners bored out and re-sleeved.

Just for the record, the liners had been press fit only (not stepped, not top hat & not pinned)


Thumbnails of attached images:

Filename: Dropped liners (2).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 898
Filesize: 163.94 KB
Image size: 1024 x 768 Pixels

Filename: Dropped liners (1).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 828
Filesize: 128.89 KB
Image size: 1024 x 768 Pixels

Filename: Dropped liners (3).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 801
Filesize: 134.29 KB
Image size: 1024 x 768 Pixels

Filename: Dropped liners (4).JPG
Filetype: File Type Information for: jpg jpg
Downloads: 839
Filesize: 120.49 KB
Image size: 1024 x 768 Pixels

This post has been edited 1 times. Last edit on Jun 24, 2014 3:35 pm by cahallett.  

Jun 25, 2014 7:12 pm
ray sherratt Offline
Member
Registered since: Jul 05, 2012
Location: wirral cheshire


Subject: Re: 16/80 head gasket problems
I see the sump is still fitted, is it possible the liners are
down to a bottom step. At Headshop we have just fitted
new liners to an Alvis, one had moved down and smashed
by the con rod. On inspection the liners had only 0005"
interference fit, and no lower step. Having had a good
look at your photos there seems to be a good fire ring
mark on the block around the cylinders, I wood be surprised
if the liner slip is you problem.

Ray.
This post has been edited 1 times. Last edit on Jun 25, 2014 7:23 pm by ray sherratt.  

Jun 26, 2014 11:21 am
cahallett Offline
Member
Registered since: Apr 02, 2012
Location: -


Subject: Re: 16/80 head gasket problems
Hello Ray,
Thanks for your reply/comments.
I don't know what the interface fit on these is but I do know there is no step.
I think for peace of mind the engine has to be removed, dismantled, checked and then rebuilt (time permitting).

The water in the oil is probably due to a failure of the low water pump seal (or so I have been advised) and if this is the case it should be clear to see the evidence once the water pump is removed.

Thanks again for your comments

Chris


Thumbnails of attached images:

Filename: Block 16-80.JPG
Filetype: File Type Information for: jpg jpg
Downloads: 831
Filesize: 179.14 KB
Image size: 1280 x 718 Pixels

 

Pages (1): [1]


All times are GMT