Lagondaforum

Hello Guest! (New posts) Forum


Expand and collapse Topic Options
Pages (2): [1] [2]
 Show first unread post

Jan 16, 2017 10:17 pm
davidbracey Offline
Member
Registered since: Aug 10, 2012
Location: Maidstone, Kent


Subject: Re: Chassis lubrication fitting wanted
I'm definitely still learning about these cars. I look forward to doing some living some time soon!

I've been reading up about the RR one-shot chassis lubrication system and they made two different versions of injectors/drip feed nozzles, with different volumetric flow rates. Different amount of oil dispensed according to the application point. I can't believe a suspension point needs much so guess that if I can't find the genuine article I'll buy a RR one and see what I can do with it.

If any of you wise men that frequent this forum have any more advice for me I would be very grateful.
David Bracey
This post has been edited 2 times. Last edit on Jan 17, 2017 7:06 am by davidbracey.  

Jan 17, 2017 7:57 am
DavidLG45 Offline
Member
Registered since: Dec 05, 2007
Location: -


Subject: Re: Chassis lubrication fitting wanted
A bit more information - all relating to R-R. Surely these were bought in items at the time so likely to be the same source for Lagonda?

http://www.fiennes.co.uk/Parts/Catalogue/A/AE

A range of different ones. Presumably the S1/ZE1 etc is the size of the hole? See table (copied from the Bodice article):

Pin #   Diameter     Bijur part #
        
00      .0501       A1475-00
0       .0497       A1475-0
1       .0490       A1475-1
2       .0480       A1475-2
3       .0468       A1475-3
4       .0448       A1475-4

Overhauling link:

http://www.boddice.co.uk/bmai101.htm#Drip

Is there any reference number on your broken one, David?
Where was the one you broke feeding oil to?

David
This post has been edited 1 times. Last edit on Jan 17, 2017 8:00 am by DavidLG45.  

Jan 17, 2017 9:58 am
davidbracey Offline
Member
Registered since: Aug 10, 2012
Location: Maidstone, Kent


Subject: Re: Chassis lubrication fitting wanted
Thanks David,

I spoke with Fiennes yesterday and they said the ones they make are their own 'uprated versions' - whatever that means. No, my snapped one doesn't have any markings but I'm not convinced they've the same threads either. Not that that is an insurmountable problem of course.

Fiennes suggested parts ZS4 and AE070. I have to pass their way in a few weeks so might pop in and compare if I can't find a direct replacement.

The frustrating thing is, that with the number of these cars that have been broken up or heavily modified there must be hundreds of these fittings languishing in sheds and garages.
David Bracey
 

Jan 17, 2017 11:57 am
DavidLG45 Offline
Member
Registered since: Dec 05, 2007
Location: -


Subject: Re: Chassis lubrication fitting wanted
Hi David,

I guess many hard to find parts are lurking at the backs of garages or thrown away.

Can one assume if there are no markings Lagonda used the same size drip plug throughout? Not a great deal of difference in the size of the biggest and smallest in the Boddice list.

Wouldn't the thread be BSP as it's a pipe fitting?

David
This post has been edited 1 times. Last edit on Jan 17, 2017 12:07 pm by DavidLG45.  

Jan 17, 2017 2:07 pm
davidbracey Offline
Member
Registered since: Aug 10, 2012
Location: Maidstone, Kent


Subject: Re: Chassis lubrication fitting wanted
I don't have any thread gauges at home but I agree that it seems as if it should be a pipe thread. However...the OD measures as 7.9mm with my Vernier which is almost exactly 5/16". The thread also appears to be too fine to be BSP. UNF is 24tpi. I have some UNF taps somewhere so will try it. The only other imperial thread I've found that looks similar is BSC (CEI) cycle threads (26tpi). Brass pipe screw threads would have been the obvious choice but there isn't a 5/16" size.

I'm going to have to identify the thread properly before I go any further - unless anyone has one they can let me have of course?
David Bracey
 

Jan 17, 2017 7:31 pm
bill Offline
Member
Registered since: Jun 08, 2011
Location: -


Subject: Re: Chassis lubrication fitting wanted
David, ring Alan Brown and see if he has anything. Not many people seem to have reinstated the chassis lubrication system so there should be lots of bits around !
 

Jan 17, 2017 7:36 pm
davidbracey Offline
Member
Registered since: Aug 10, 2012
Location: Maidstone, Kent


Subject: Re: Chassis lubrication fitting wanted
Good idea Bill. Will report back.
David Bracey
 

Pages (2): [1] [2]


All times are GMT